2022 Quicko TS100 Iron ts Replacement Various models of T Electric Iron T K KU I D24 BC2 C4 C1 JL02

Quicko TS100 Iron ts Replacement Various models of T Electric Iron T K KU I D24 BC2 C4 (not ) Features: High quality It's a internal-heated heating core specially for TS100, t and heater as a whole. Specifications: Type: TS-BC2, TS-I, TS-D24, TS-C4, TS-K, TS-KU, TS-B2,TS-C1,TS-ILS,TS-JL02,TS-BC3 Quantity: 1pc Length: approx. 103.5mm-109mm Weight: 10g-11.2g Color: Sier Package includes: 1 x Replacement Solder T NOTE:The new TS t will experience temperature jump hen first used. Don't worry, this is normal. When you use it a few times, the temperature will gradually stabilize.

FAQ： 1. Why the temperature of the new T12/TS solder t is jump? Because the inside heating core of the new T12 solder t  did not go through the high temperature, so the first time to use will be a bit of temperature, generally without special treatment, the normal use of 1-2 days after the basic will not bounce. Such as the need to immediately effective, the general proposal to adjust the temperature to 380 ℃ -400 ℃, side of the solder t to the t of tin, burning 5-10 minutes after the shutdown, until the solder t of the cooling and then re-boot! ( if 1 times no effect, then can be repeated 2-3 times). T12 is pulsating temperature warming, even if the display temperature is fing, the t of the real temperature is completely stable. T12 jump temperature also are connected with the temperature control board of procedures, power of electrostatic and if it connect the ground. 2. What the problem of attention when we use the T12/TS first time? T12 t heating speed is very fast, when the new solder t connect the electricity, it must be tinput immediately to the solder t, for protection, due to heating up fast, just need 6-10 seconds, no have more time to you for preparetion. so the ant is prepare the it which will be welded, and finally boot power, and each welding gap or the end, should be more on the tin to protect and then shutdown, so it can avoid to tin the new sold t is difficult, especially the T12 t type of iron, such as T12-I / T12-IL / T12-BL / T12-ILS and so on! 3.What are the precautions for using the T12/TS t? a. If can use low temperature, then do not high temperature: T12/TS is constant temperature control, the general recommended working temperature control between 300 ℃ ~ 380 ℃, higher than 380 ℃ damage the coating of solder t and cut down the PTC life! b. Do not dry: the first time to use solder t, should be wrapped while heating a layer of tin. If it's without work, at once shutdown! c. Diligent to clean: before shutting down, use a wet sponge or detin the ball to remove the t of the oxidation of debris, on the tin after the shutdown power off! d. Standard operation: Do not violent collision the solder t, do not stamp the top of the hard objects, but can not be used to hot plastic and other materials, specifically reminded that friends like tin should avoid the iron and other hard metal knock tin, the heating core of T12 is in the head of the solder t, often percuion is a al damage to T12/TS! e. Le use of scaling powder: scaling powder can not be used, can be used as le as poible! When scaling powder help make beautiful and reliable welding at the same time, but also greatly speed up the consumption the coating of the solder t, T12 heating core high temperature position is very near of the Nozzle t of the solder t,Scaling powder in the fear of threat to T12 head preing parts. 4.How to do when T12/TS t does not absorb tin? T12 iron head does not absorb tin, generally there are two reasons: A. The head of solder t is severe oxidation can not absorb tin. B. Temperature can not rise up then can not tin. C. The head is oxidized and can not the tin, you can use the iron to clean the ball gently, then use the wet sponge rub and then heat the tin. D. serious oxidation of tin, you can use more than 900 mesh sandpaper gently rub, with a small wooden board, in the board to dig a small hole, put the rosin and tin in the hole, put the head of solder t insert the hole, while heating and putting the tin,If you can prepare a tin stove, use scaling powder into tin stove put the tin to repair! E. If T12 temperature can not rise up, the multimeter transferred to 20Ω stalls, test T12 solder t positive and negative ring resistance. 8-10Ω belongs to the normal range, the factory standard is 8.4Ω, after using the resistance will be slightly changed! Payment 1. 100% payment before delivery, please make sure you have make out the complete correct information, include full name, detail addre, post code, phone number, the goods will be shped to the addre that you left in the order, and “P.O. box” is not allowed in the addre. 2. We prefer payment through ESCROW which is a security way for you. If you want to pay by other ways, please contact us. 3. When you place an order, please choose a shping method and pay for the order including the shping fee (except for free shping). Shping 1. We will send the it within 1-7 days once your payment is completed. 2. We only sh to confirmed order addrees. Your order addre MUST MATCH your Shping addre. 3. The images shown are not the actual item and just are for your reference. 4. SERVICE TRANST TIME is provided by the carrier and excludes weekends and holidays. Transit times may vary, particularly during the holiday season. Feedback 1. Our goal is 100% positive feedback and 100% customer satisfaction. We do our best to serve our customers the best that we can. Your satisfaction and positive feedback is very ant to us. 2. If you are not satisfied with the it you ordered, please contact us before leaving negative feedback. We can work together to resoe any dispute. 3. Please leave positive feedback and 5 stars if you are satisfied with our goods and services. Taxes taxes rate are made by your customs, it is vary from different countries, so all of our products don’t include any taxes, you need to pay it on your side when neceary. ... Return& 1. You have 7 days to contact us and 60days to return it from the date it was received. If this products is in your poeion more than 7 days, it is considered used and WE WILL NOT ISSUE YOU A OR REPLACEMENT. There are NO EXCEPTIONS! Shping cost is bear by buyer. 2. All returned products MUST BE in the pack and you MUST PROVIDE us with the shping tracking number, specific reason for the return, and your PO#. 3. We will , upon recet of the item in its condition and pack with all components and acceories included, AFTER BOTH Buyer and Seller cancel the transaction from aliexpre. OR, you may choose to have a replacement.

About shping
Shping and Pack All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.