Constant current electronic load Discharge 9.99A 60W 30V battery capacity for 18650 12V 24V battery

RM1307731645732355

If you want buy the Shell Box pls Click this link New upgrade features of v3: 1. The test current range is changed from 0.20-9.99A to 0.10-9.99A. 2. The lower limit and termination voltage range is changed from 1.0-25.0V to 0.9-28.0V. 3. Support non-operational voltage display. 4. Increase the support for four-wire test in electronic load mode, with independent four-wire voltage indicator. 5. The LED indicates that the setting digit is changed to the current setting digit and fing indication V3 (NEW-30A1) 60 Electronic Load User Manual Working power supply: DC12V stabilized voltage (11-13V) not le than 0.5A Interface: 5.5*2.1 positive pole inside the round mouth Working mode: single mode constant current (CC) Discharge current: 0.10-9.99A step 0.1A or 0.01A Discharge current error does not exceed: 0.7% plus or minus 0.01A Capacity test error does not exceed: 0.5A 2%, 2A 1.5%, 5A and above 1.2% Setting range of offline (termination) voltage: 0.9-28.0V step 1V or 0.1V Discharge voltage: 0.90-30.00V (affected by MOS internal resistance and other loes, the measured input 1V can support 6-7A current, and the measured voltage needs to be greater than 1.3V at 9.99A) Voltage measurement error does not exceed: 0.8%+-0.02V Power: 62W super power automatically limits the current (for example, for 60W, it can open 9.99A at 6V and only 3.00A at 20V) Battery test statistical value limit: 999.9Ah or 9999Wh, the test stops when the value is reached (the one that comes first is the stop condition) Circuit board size: 60W 112mm*70mm*57mm (the fan protruding from the board is about 12mm) Weight: about 170g (60W) Fan control: intelligent fan control (the fan can automatically and continuously change according to the temperature) Protection function: overheat protection "otP", instantaneous over power protection "oPP", over voltage protection "ouP", re connection protection, power supply voltage abnormal protection. Instructions: One: Function mode setting (default factory is electronic load mode): Pre and hold "ON/OFF" while powering on the , and then release the on when Fun* is displayed, then enter the function setting menu. Change the setting by rotating the knob, switch to the next step by preing "ON/OFF", and set in the following order: 1. Mode setting "Fun1" is the electronic load mode, and "Fun2" is the battery capacity test mode. 2. switch setting The "bEon" is on and the "bEoF" is off. 3. Display brightne setting "Lt-1" "Lt-2" "Lt-3", three brightne levels are optional. After finishing this item, pre "ON/OFF" again to save and exit the setting. Then the restarts and enters the normal working state. Two: Electronic load mode: 1. Turn on the 12V working power supply, make sure it is in the stopped state ("RUN" light is off, otherwise pre "ON/OFF" to turn off), connect the tested power supply to the power input port (P+P-), if used For four-wire connection, please connect the voltage detection line to the (V+V-) socket at the same time. When the voltage of the tested power supply is higher than 1V, the voltage will be displayed automatically, and the "L-4" light will be on when the four-wire mode is recognized. Note: When wiring, do not touch the with the screwdriver, and do not connect the re polarity. 2. Set the current and lower limit voltage through the knob. Rotate the knob to set the value of the current setting position. Pre the knob to switch the setting digit. The number of the current setting position will f. If you do not operate for more than 3 seconds, it will automatically exit the setting. Back to normal display voltage and current. 3. Pre "ON/OFF", the load starts to run, "RUN" lights up, the circuit applies the set discharge current to the input tested power supply, and the actual input load voltage is displayed upwards, when the voltage is lower than the set lower limit voltage , "RUN" light fes and the shortly sounds. 4. The current can be modified at any time during the test. If the lower limit voltage needs to be modified, the load must be turned off before modification. Note: When in the alarm state, the current can only be adjusted down but not up! The 's automatic power-down save function can save the set and running status. When the power is turned off and re-powered, the state and data before the power-off will be completely restored. Three: Battery capacity test mode: 1. The battery under test should be fully charged with a dedicated charger first! 2. Power on the to enter the battery capacity test mode, connect the positive and negative poles of the battery current circuit to the P+P- terminal, if using a four-wire fixture for testing, please also connect the positive and negative poles of the four-wire fixture voltage test interface to V+V -port. The will display the battery voltage. If the four-wire voltage test line is connected correctly, the "L-4" light will light up at the same time. 3. Set the discharge current and discharge termination voltage by rotating the knob (refer to 2: 2. Descrtion for specific methods). After setting, pre "ON/OFF". The will first test the battery and circuit, and then enter the test. If there is a fault code, please refer to the following descrtion. 4. During the test, the upper digital tube will display the battery voltage, current discharge capacity Ah and current discharge energy Wh in turn. When the discharge is over (the battery voltage is lower than the set voltage), the displays the data stay in Ah and fes quickly, accompanied by the bee The makes a rapid alarm sound. 5. Pre the knob or start-stop switch to stop the alarm. You can turn the knob to view the battery discharge data including discharge capacity Ah, discharge energy Wh and platform voltage V. After preing "ON/OFF" again, the cleared data will return to the initial Set the interface to test the next battery. Supplementary note: 1. During the battery test, the discharge current can be adjusted at any time. If you need to readjust the termination voltage, you can pause the discharge modification by preing "ON/OFF" (pausing the discharge will return to the setting page, and the discharged data will not be lost. Long pre "ON/OFF" to clear the data). 2. The automatically saves the set when power off, and records all and states when the power is off during the test proce and the alarm state at the end of the test. All and states are automatically restored after re-powering. Fault protection code and meaning: Err1: The battery voltage of the capacity test is extremely high. Err2: The battery voltage is lower than the set termination voltage, the battery is not connected or the battery is connected rely. Err3: The internal resistance of the circuit is too large or the battery cannot withstand the set discharge current. Err4: Circuit fai. Err6: The working power supply is not suitable, please use a standard 12V regulated power supply, and the power supply current is not le than 0.5A. otP: Overheat protection. Ert: The temperature probe is faulty or the temperature is too low. ouP: The voltage is extremely high in the electronic load mode. oPP: Super high instantaneous power in electronic load mode

About shping
Shping and Pack All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.