Craft Silicone Aromatic Cement Plaster Pot Mold DIY Soap Making Silicon Mould

Features:
● The main component of silica silica is silica , a natural component found in sand, and crystal. Not rubber rubber, not plastic plastic! Silica is a on the beach, low in carbon and environmentally friendly.
● Silicone has high flexibility, corrosion resistance and temperature resistance. It is suitable for cooking, baking and simple and practical.
● Through testing, health and natural antibacterial, can prevent the breeding of bacteria and fungi. Therefore, there are a large number of silicone products in baby products and supplies. Pacifier, silicone plastic and so on.
● Recyclable, durable and low energy consumption.
● It has stable structural mechanical properties, so it has good temperature resistance and wide temperature range. The lowest temperature resistance is 40 degrees below zero, the highest temperature is 230 degrees, and it is evenly heated by heat.
● It has corrosion resistance to cleaning agents and kinds of corrosive substances and is easy to clean.
● After use, any raw materials will not stick to the mold.

Specifications:
Material: Silicon
: Grey
Total Size: 190X140MM/7.5"X5.5"
Shape Size:
80X60MM/3"X2.4"
80X55MM/3"X2"

Package included:
1 Set x Soap Making Silicon Mould(4 Molds)

Precautions:
1) Do not touch the open flame directly or close to the heat source (such as the oven heating tube). It is recommended that you place the mold in the middle or upper position of the oven during baking, and keep at least 5cm from the heating tube.
2) Use a neutral detergent in a dishwasher or hot water to clean with a sponge. Turn the mold over when cleaning, and the cleaning effect is better.

Instructions for use:
1. Before using for the first time, it can be cleaned with water or detergent to remove surface dust. Before the mold is used for baking, a small amount of butter can be applied to the inside of the mold. When using continuous mode, if there is an empty slot, water can be added to the empty slot, and air burning is prohibited.
2. After each use, soak in the diluted detergent for 10-30 minutes. When cleaning, please wash it with cloth. Do not use rough cleaning balls and items to avoid scratch damage to the mold. After cleaning, please dry it and place it in the storage box. The silica is easy to react with static electricity and will adsorb tiny particles and dust in the air. When not in use for a long time, avoid direct exposure to the air.
3. When used in the oven, be sure to place it in the middle of the oven, keep a distance of about 10 cm from the heating tube, and keep a distance of 5 cm from the wall of the oven to avoid high temperature damage to the mold.
4. Some molds have cracks. This is cut at the time of leaving the factory, which is convenient for buyers to demould. If you do not cut, you cannot release the mold. When using, put on the plastic wrap or put on the rubber band and pour the into the incision.










a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a