DIY Incubator Spare Part Poultry Incubator Controller Set Controller Accessories EU

Features:
● Exhaust fan: uniform heat dissipation, low noise, long use time.
● Heating piece: constant temperature PTC heating, the hatching temperature is guaranteed.
● Panel: panel, one-key incubation control.
● Humidity probe: digital probe, stable performance.
● Temperature probe: precision temperature sensor, accurate information collection.
● Motor interface: This interface connects the motor and the egg tray.
● Egg turning motor: special accessories for household incubator motor incubator.
● Designed for incubationDIY Handmade Incubator Shocks Experience.

Specifications:
- Rated : 80W
- Plug: AU plug, UK plug, EU plug
- Temperature control range: 37°-39°
- Rated voltage: 220V/110V/220+12V
- Turnover frequency: 2H/time
- Scope of application: 48pcs, 56pcs, 96pcs, 112pcs
- Panel size: 33.2x3x10.2cm/13.1x1.2x4.0''

Package Included:
1x Poultry Incubator Controller Set

Temperature and humidity settings
1.
After connecting all components in the figure, turn on the , you will hear the alarm sound caused by temperature/humidity, manually press to cancel the alarm.

2. Set the temperature and humidity, change the number of incubation days
Press the setting key, press "+/-" to select the desired temperature, set the humidity and the number of incubation days in the same operation (repeat twice), and finally press the setting to exit the setting. (Note: The factory setting is 37.8°. You can set 37.6° according to the above method. After setting the incubation days, the machine restarts to take effect.)

3. Low/high temperature alarm setting
Press and hold the setting key for 3 seconds, press "+/", the display "AL", then press the setting key, press "+/-" to select the low temperature . Press and hold the setting key for 3 seconds, the display "AH", set the high temperature alarm as above.

4. Humidity alarm setting
The humidity is factory set at 45%, no need to set. (If you need to set, you can set according to the temperature setting mode, the display "AS".)

5. Calibration temperature sensor reading
The normal temperature reading is set at 0°. If it is not correct, it can be set. The method is the same as above, and the display "CA". )

6. Temperature upper/lower limit set
If the HS (upper limit set) is set to 38.2 and the LS (lower limit set) is 37.4, the temperature can be changed from 38.2 to 37.4, and the lower limit should be at 37.2.

7. Heating setting
The HU and HD are set by the factory, no need to set.




a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a