HiFi Vacuum 6A2 Tube MM Phono Vinyl Record Player Stereo Tube Pre amp Amplifier Turntable Phonograph DIY 12V-tube phono EU Plug

Product descrtion:

Specifications:

Output level: 600mV @3mV 1KHz Signal to noise ratio: ≥98dB Working voltage: DC12V 1.5A Dimensions: 118.5*98*33MM (without protruding knobs and terminals) Frequency response: RIAA compliant Distortion: 0.1% Operation Steps: 1. The gear switch is in the OFF state. 2. Insert the supplied tube into the tube holder in the direction (the tube does not matter, che whether the lower pin is deformed before installing the tube, and the deformation can be red by hand). 3. Connect the sing-out output cable to the audio input connector. 4. Connect the rear-end device that needs an external connection to the audio output connector. 5. Connect the DC12V power supply. 6. Rotate the gear switch to select the desired gain gear. 7. When the preamp input is input, the phono input will automatically switch to the preamp input. 8. Input interface： (can be connected to CD, DAC decoder, mobile phone, TV, etc.) 9. Audio output interface： (such as amplifier, amp, active speaker, etc., red to the right channel, white left channel) Common problem: Q: All my lines are connected, but there is no sound output? Answer: 1. Che if the gear switch is in the OFF state. Che whether the tube light is on after the switch is turned on. If the fault still exists, replace the power supply with the same voltage output (must be 12V) and test again. 2. If the indicator light is on and the gear position switch is also on, unplug the power supply and re-insert the tube. 3. If both of the above are normal, che if the playba device of the input source is paused, muted, or the volume is at its minimum. Q: Why is the sound broken? A: This product is a pre-stage product, and it also has amplifying effect. If the volume of the post-stage device is adjusted to the maximum and the pre-stage is also adjusted to the maximum, it is easy to be distorted. At this time, you only need to move the pre- or post-level. The volume can be adjusted smaller. Q: Why does the speaker have a large current sound? A: If you are not using the standard power supply, please replace the power supply before testing. A lot of power supply in the market has a large interference coefficient, which will cause a large current sound. Q: Why do I not play the sound source after I plug in the input cable, and the speaker will have a loud beep? Answer: 1. When the unshielded signal line is used, the interference signal will enter the amplifier for amplification. If you hate this sound, you are advised to replace the shielded signal line or unplug the signal line. 2. Che if the grounding of the player is connected. If the ground wire is not connected, there will be a lot of noise. Q: Why do I use MM to put input, it has no sound? A: Che if the pre-stage input is still plugged in. If the pre-stage input is plugged in, then the input will not sound, and the pre-stage input line must be unplugged. Q: Why did the pre-biliary level buy ba and start listening to the sound is very hard, the tri-band is not very clear, but after 1 day of work is normal? A: The tube is a very sensitive device. The temperature should generally reach a certain level to achieve the best effect. Therefore, the sound is very natural after about half an hour of warming up. Q: Can I replace the tube upgrade? A: Yes, at present, we have tested and matched 6K4/6J4/GE5654/6AK5/6*1n, which can be directly replaced. Different tube sounds will be very different. Q: Can I replace the tube with the power supply? A: No, it is very easy to burn the tube because the inside of the hine is working at high voltage. If the hot-swappable tube burns out, it may damage the hine. Warning: 1. Do not open the case privately. Improper handling may result in electric sho. 2. Please use the switching power supply of the regular manufacturer, otherwise the risk of damage to the hine will be damaged. 3. Do not place the hine in a high temperature and high humidity environment. 4. Please disconnect the input and output cables before powering off, otherwise the impact sound may damage your speakers. 5. Do not replace the tube type that does not match, otherwise it will burn your tube and hine.

About shping
Shping and Pa All it will be double cheed and well paed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the paage to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedba, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at cheout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbaYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedba for the transaction.