OPA541 Module Audio Amplifier HiFi AMP 5A Current High Voltage High Current Driveable coil motor Sound amplifiter

Highlights:

1. OPA541 ch is a kind of power operational amplifier which can operate from power source to ±40V, and provides continuous output current up to 5A. The internal current limiting circuit can be a with a single external resistance to protect the amplifier and load from fai conditions.

2. The oPA541 device uses a proprietary bolar transistor proce. Currently used hybrid power amplifiers require two current limiting applications that do not need to be modified.

3. The seal of oPA54 1 is into 11-pin electric plastic paage or 8-pin gas seal of industrial standard. Electric Plastics will be paaged with curium lead frames to maximize heat transfer.

4.The T0-3 seal is isolated from the circuit so that it can be directly installed on a without special insulators.

OPA541 module shping list

Physical module + PDF schematic diagram + after- technical support + electrostatic bag pa + shoproof foam

Ts:

(1) The module interface of our shop is clear and the performance is stable. Please perform functional verification under the corresponding experimental conditions in conjunction with the schematic diagram provided by our shop.

(2) The basic parameters of this module are in the details page, providing PDF information of the module information; engineering doents are not provided, please be clear to the buyer, if you have operational probl, you can consult customer service.

(3) Buyers, before using the module, please read the details page of this module to understand the power supply and use restrictions, to avoid damage to the module due to improper operation.

(4) The modules of our shop are guaranteed to provide real module parameters, functions and tures, and all modules are shped only after detection.

Please contact customer service after purchase. We will send the information to your mailbox.

​

Module parameters

Module model: OPA541

Module type: low frequency power amplifier

Input signal form: single-ended

Input voltage range: 2Vpp (MAX); generally within the power supply range

Module input impedance: 1K ohm

Module supply voltage: ± 10V ～ ± 40V

Module supply current: ± 5A; large output current requires large supply current

Module output impedance: low impedance

Output voltage range: 68Vpp (MAX); in the case of positive and negative 40V power supply

Output current: 5A (MAX)

Output power: 50W (MAX)

Module gain: 33 times; the default gain is 33 times, the first level is 11 times, the second level is 3 times, G1 = R1 / R2 + 1, G2 = R7 / R4 + 1

Input offset voltage: 200uV (MAX)

Input offset drift: 2uV / ℃ (MAX)

Input bias current: 125nA (MAX)

Input voltage noise: 35nV√Hz (1KHz)

Module weight: 125g

Module protection: none; no re connection protection, unlimited current protection

Module weight: 125g

Module specifications: 96 * 64 * 41mm; length * width * height- size

The module becomes hot: there is a heat sink, and forced air cooling is required at high current

Module heating factors: the input and output voltage is too large or the module is damaged

Module working temperature: -40 ℃-+ 75 ℃ industrial grade

Module features: positive and negative power LED indication

Application range: small signal amplification, audio signal amplifier, motor drive, servo amplifier, etc.

Module interface type: SMA signal signal input and output, 5.08 blue power card wire holder

Module descrtion

The OPA541 module is a power operational amplifier capable of operating with a power supply up to 40 V and providing continuous output current up to 5 A. The internal current limiting circuit can be controlled by the user using a single external , while protecting the amplifier and the load; so that it is not affected by the fault condition. Suitable for motor-driven speaker drive, transformer drive and audio amplifier. It can also amplify triangle wave, sine wave and square wave signals.

Precautions for using the module

(1) The power consumption of the module is large, and the power supply needs to have a certain margin. It is recommended to use a power supply with a current drive capacity greater than twice the output current. The module can only be powered by dual power supplies.

(2) In order to avoid unneceary interference, it is recommended to use a linear power supply, the power supply cannot exceed plus or minus 40V.

(3) It is recommended to use the SMA to BNC cable to directly observe the output signal for the output signal. Poor contact or poor quality wires may cause signal attenuation or exceive noise.

(4) The SMA port is not available for power output, and a blue terminal blo must be used. The SMA port is for observing the signal and must not overpower.

(5) Due to the large power consumption and heat generation, pay attention to ventilation and heat diation for long-term work, and add fans to strengthen heat diation if neceary.

(6) Since the module has a fixed magnification and no external protection circuit, it is recommended to confirm the output power and amplitude before loading to avoid damage to the module.

input:Vpp=100mV Freq=1.00KHz

Frequently asked questions

​

Q: Is the magnification fixed? How to adjust?

A: The default magnification of the module is 33 times. If you need to adjust the magnification, you can only replace the on the board. The is 0805. The calculation formula is given in the parameter details.

Q: Can the module directly drive the coil?

A: The module can drive the coil, but the internal resistance of the coil is required to be greater than 4 ohms. If it is le than 4 ohms, a series power resistance is required, otherwise the module may be damaged.

Q: Can the module amplify square wave or pulse? What is the module bandwidth?

A: The module can amplify low-frequency square waves or pulses. Because it is an audio amplifier, the total bandwidth is not high. Signals within 100K can be amplified. The module is compatible with DC input.

Q: Can the module be enlarged 1: 1? That is, only the current is amplified. ?

A: The module can support 1: 1 amplification. You need to modify the resistance configuration magnification yourself. It is not recommended to directly configure the op amp follow mode, which is easy to self-excitation. It is recommended to change to resistance attenuation first, and then operation amplification; the total gain is 1 Just fine.

Q: Why the input sine wave output is square wave? What is the output current? What is the output power?

A: Generally speaking, the input signal is too large, and the op amp is amplified to the cut-off distortion, which is the square wave, or the supply voltage is not enough. Can reduce the input signal and increase the supply voltage to soe. The output current of the module is determined by the output voltage and the load. I = Uout / R. Similarly, the output power P = U * I is also determined by the output voltage and the load resistance. When high power is input, heat diation grease and air cooling can be added.

Q: Can I use the second level directly instead of the first level?

A: You can use the second stage directly, but you need to remove the ch of the first stage, and then input the signal from OUT1. Otherwise, the first-level ch will affect the signal input.

About Elecdemo:

Elecdemonded in 2015 , Elecdemo is a well-established technology company that integrates supply , R & D , prodund s , supporting agents , franchises , customization and bulk purchases . We are committed to provid our customers with the best electronic functional module products at the lowest price . We have a profeional design and production team to providecustomer service to help our customers greatly improve the efficiency of development，learn and research.

About Transpiration:

1. Global shping, (except for some countriesand APO/ FPO)

2. duties: Taxes are not included in theprice or shping costs. Customs fees are the responsibility of the buyer.

3. If the paage is not delivered within 30 days. please contact us. We will help you soe the problem.

About Delivery:

1. We will proce the order in time after the payment is confirmed. Due to the difference in inventory status and time, we will choose to sh from our first warehouse for fast delivery.

2. We only send to the confirmed order addre. Your order addre must match your shping addre.

3.Service transit time is provided by the carrier, excluding weekends and holidays. Delivery time may vary, especially on holidays.

About guarantee:

1. manufacturers limited warrantyon defective it(excluding it damagedand/or misused after recet). The acceory is baed by a 3 month warranty

2. The displayed image is taken in real time, but due to different production batches, thecolor may be different. The ture is for reference only, and the actual object is subjectto the final one

3. The defective item must be reported and reurned within the warranty period(if poible,in the pa

4. If the product features do not match the advertisement, we will bear all shping costs.

About feedba:

1. If you are satisfied, please leave 5 stars positive feedba, we are very honored to receivea generous real aement and photos, th !!!!

2. For any product or shping probl, please contact us before opening a dispute orleaving any feedba/negative feedba, we will try our best to soe the problem untilyou are satisfied.

Returns and s:

1. You have 7 days to contact us and you will not be able to return from the recet date after30 days. If the item has been owned by you for more than 7 days, it will be considered usedand we will not or replace it. with no exceptions! Return shping costs are theresponsibility of the buver.

2. All returned it must be in pa, you must provide us with a shpingtraing number.

3. If there is a return, please contact us in advance, we will help you soe it. If it cannot besoed online, we will accept your return and it to you.

.

About shping
Shping and Pa All it will be double cheed and well paed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the paage to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedba, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at cheout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbaYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedba for the transaction.