Station DIY Welding TIron For FX951 Hand8S Melt Tin Repair Tools 1pcs T12-1401

KSGER T12-1401 1402 1403 OLED/LED Station DIY Welding T For FX951 Hand8S Melt Tin Repair Tools

Descriptions:

1.Make use of raw material-copper oxide, use special molding machine to proce, the tsize very precise;

2.Lead-free alloy electric plating close-grained, very long life about 3-4 times compared to domestic products;

3.Product surface use special material handling, tend with coating proceing, so as to ensure the tnot turn blaunder the high temperature;

4.Good performance in tin-on and tin melting, solder joints uniform, and fluent;

5.With high anti-oxidation, good moist performance, quithermal conductivity, the product quality has reached the world's top

Features:

1.Applied to station FX-951/FX-952/FX-950/FM 203;

2.Lead-free, envment-friendly, 100% conformed to ROHS standard, lead < 0.1% wt;

3.The technical indicators reach to standard;

4.Use under 400 degree temperature(±20 degree), it can have 50000 solder joints.

XA High-gradeT12 twith low current plating hard blachrome proce, proce advantages:

1. Blachrome plating of high thermal stability, heated to 480 degrees appearance does not change. Blachrome plating corrosion resistance is better than ordinary decorative chrome layer. 2. Chromium layer dense, the hardne of the coating up to 1000-1100KHN, wear high temperature anti-corrosion ability. 3. Coating thickne uniformity, reduce the high current density of the thideposition. 4. Smooth coating, fine light, beautiful and delicate. 5. blawith solemn sense, blais a permanent charm of the tone.

FAQ：

1. Why the temperature of the new T12/TS solder tis jump? Because the inside heating core of the new T12 solder t did not go through the high temperature, so the first time to use will be a bit of temperature, generally without special treatment, the normal use of 1-2 days after the basic will not bounce. Such as the need to immediately effective, the general proposal to adjust the temperature to 380 ℃ -400 ℃, side of the solder tto the tof tin, burning 5-10 minutes after the shutdown, until the solder tof the cooling and then re-boot! ( if 1 times no effect, then can be repeated 2-3 times). T12 is pulsating temperature warming, even if the display temperature is flashing, the tof the real temperature is completely stable. T12 jump temperature also are connected with the temperature control board of procedures, power of electrostatic and if it connect the ground. 2. What the problem of attention when we use the T12/TS first time? T12 theating speed is very fast, when the new solder tconnect the electricity, it must be tinput immediately to the solder tip, for protection, due to heating up fast, just need 6-10 seconds, no have more time to you for preparetion. so the ant is prepare the it which will be welded, and finally boot power, and each welding gap or the end, should be more on the tin to protect and then shutdown, so it can avoid to tin the new sold tis difficult, especially the T12 ttype of , such as T12-I / T12-IL / T12-BL / T12-ILS and so on! 3.What are the precautions for using the T12/TS tip? a. If can use low temperature, then do not high temperature: T12/TS is constant temperature control, the general recommended working temperature control between 300 ℃ ~ 380 ℃, higher than 380 ℃ damage the coating of solder tand cut down the PTC life! b. Do not dry: the first time to use solder tip, should be wrapped while heating a layer of tin. If it's without work, at once shutdown! c. Diligent to clean: before shutting down, use a wet sponge or detin the ball to remove the tof the oxidation of debris, on the tin after the shutdown power off! d. Standard operation: Do not violent collision the solder tip, do not stamp the top of the hard objects, but can not be used to hot plastic and other materials, specifically reminded that friends like tin should avoid the and other hard metal knotin, the heating core of T12 is in the head of the solder tip, often percuion is a fatal damage to T12/TS! e. Le use of scaling powder: scaling powder can not be used, can be used as le as poible! When scaling powder help make beautiful and reliable welding at the same time, but also greatly speed up the consumption the coating of the solder tip, T12 heating core high temperature position is very near of the Nozzle tof the solder tip,Scaling powder in the fear of threat to T12 head preing parts. 4.How to do when T12/TS tdoes not absorb tin? T12 head does not absorb tin, generally there are two reasons: A. The head of solder tis severe oxidation can not absorb tin. B. Temperature can not rise up then can not tin. C. The head is oxidized and can not the tin, you can use the to clean the ball gently, then use the wet sponge rub and then heat the tin. D. serious oxidation of tin, you can use more than 900 mesh gently rub, with a small wooden board, in the board to dig a small hole, put the rosin and tin in the hole, put the head of solder tinsert the hole, while heating and putting the tin,If you can prepare a tin stove, use scaling powder into tin stove put the tin to repair! E. If T12 temperature can not rise up, the transferred to 20Ω stalls, test T12 solder tpositive and negative ring resistance. 8-10Ω belongs to the normal range, the factory standard is 8.4Ω, after using the resistance will be slightly changed!

About shipping
Shipping and PaAll itwill be double checked and well packed before sending.Itwill be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for remote areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedbafor the transaction.