SuperOBD2 Ch tuning Box OBDII Interface Plug and Drive OBD for Save More Torque Power Than NitroOBD2 EcoOBD2

Seller's Warming Ts: Very ant

Usually surface mail will takes 1-2 months or more, won't have uptate until it arrives your country, please do not open the dispute casually.

Descrtion:

Super OBD2 is a Plug&Drive Ready device to function the increasing the performance of engine. Super OBD2 is easy to install. Just plug it into the OBD2 connector of cars. Super OBD2 fits all car from the year of 1996. It works based OBD2 protocols as remaping the Car's computer ECU. After driving 200 km road total, Super OBD2 adjusts itself to the car, according to the drivers' habits and always keeps remaping the ECU to increase the performance of engine.

Attention:

Reset on Design, easier to operate than nitroOBD2 Reset Key for factory reset function. Pre the reset on for about 5sec to reset.

What does NitroOBD2 make?

According to your driving habits,  NitroOBD2 makes new map in the car's computer ECU to increase the performance of your car. As you driving much more KM/Mile, it renews the map. Thus it keeps the vehicle's power and torque increasing.

What is NitroOBD2 Ch Tuning Box?

NitroOBD2 is a Ch Tuning Box which can be plugged into OBD2 connector of your car to increase the performance of your car.

When it plugged into OBD2 connector, NitroOBD2 receives the information from the car computer ECU. With the received data from ECU,

NitroOBD2 adjusts the boost preure, quantity of fuel, injection timing and preure to increase the performance of your car.

NitroOBD2 Ch Tuning Box does not exceed the manufacturer requirements. It works only within the tolerance of the engine.

NitroOBD2 finds out the hidden power of your car. NitroOBD2 does not damage the engine and the car computer ECU or not cause any negative effects to the car factory setting.

NitroOBD2 does not change any of the settings permanently. To turn back to the car's settings, just unplug NitroOBD2 from OBD2 connector.

NitroOBD2 finds out the hidden power of your car.

- Up to 35% more power

- Up to 25 % more torque

NitroOBD2 is very easy to use.

Plug NitroOBD2 into OBD2 connector of your car. And turn the ignition on for 30 seconds. And Turn the engine on.

NitroOBD2 settings are optimal and the best for your car. Even the s are different for each vehicle,

there might not be a need to make an additional adjustment. NitroOBD2 will recognize your vehicle and your driving habits after around 200 km/150 miles driving,

and then NitroOBD2 adjusts itself to match your car perfectly.

NitroOBD2 works on the basis of changing the signal form ECU. As a consequence, it changes the whole injection map.

The main difference between NitroOBD2 Ch Tuning Box and Remapping tuning methods is that NitroOBD2 Ch Tuning Box is easily removable,

and after unplug you go back to the factory settings. EcoOBD2 is the cheap and safe type of tuning.

Remapping is a permanent change to your car. This is the expensive tuning and you cannot remove it.

NitroOBD2 is equped with the engine protection function and 100% safe for your car engine.

NitroOBD2 produced on the printed circuit board in SMD technology. NitroOBD2 Ch Tuning Boxes are high quality.

Installation and Calibration

1* Pull the Car Key out from the ignition.

2* Find OBD2 connector(*) in your car and Plug in NitroOBD2 Ch Tuning Box

3* Insert the key into the ignition and twist the key to the first stage. (Do not start the car)

4* Pre the reset om for about 5 sec. After releasing the om, just wait for a while about 30-54 sec. (NitroOBD2 Ch Tuning Box will communicate and establish connection with ECU)

5* Start up the engine.

6* NitroOBD2 Ch Tuning Box will recognize your vehicle and your driving habits, after around 200 km/150 miles driving and thus NitroOBD2 Ch Tuning Box will adjust itself to match your car perfectly for more fuel saving.

Each device available for LPG.

Does your car have OBD2 connector?

On-Board s, or "OBD," is a computer-based system built into all 1996 and later light-duty vehicles and trucks, as required by the Clean Air Act Amendments of 1990.

OBD syst are designed to monitor the performance of some of an engine's major components including those responsible for controlling emiions.

OBD2 necearily for cars:

- Sold after January 1, 1996 in the USA

- Sold after January 1, 2001 in the European Union

Where located OBD2 connector in your car?

1 Driver's side, underneath dasboard, in the area under the steering column,

2 Driver's side, underneath dasboard,between the driver-side door and steering column area

3 Driver's side, underneath dasboard, between the steering column area and the center console

4 Driver's side, dashboard instrument/gauge area, between the steering column and center console

5 Driver's side, dashboard instrument/gauge area, between the driver-side door and steering column

6 Center console, vertical surface  left of vehicle centerline

7 Center console, vertical surface right of vehicle centerline or on paenger side of center console

8 Center console, horizontal surface  in front paenger area.

About shping
Shping and Pack All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.